Go back to plain arduino, this had fucking broke my mind and i have no clue why

CMakeLists.txt

@@ -1,3 +0,0 @@
-cmake_minimum_required(VERSION 3.16.0)
-include($ENV{IDF_PATH}/tools/cmake/project.cmake)
-project(TEF6686_ESP32)

lib/TFT_eSPI/TFT_eSPI.cpp

@@ -191,7 +191,7 @@ bool TFT_eSPI::initDMA(bool ctrl_cs)
     .command_bits = 0,
     .address_bits = 0,
     .dummy_bits = 0,
-    .mode = TFT_SPI_MODE,
+    .mode = SPI_MODE0,
     .duty_cycle_pos = 0,
     .cs_ena_pretrans = 0,
     .cs_ena_posttrans = 0,
@@ -238,7 +238,7 @@ bool TFT_eSPI::initDMA(bool ctrl_cs)
 inline void TFT_eSPI::begin_tft_write() {
   if (locked) {
     locked = false; // Flag to show SPI access now unlocked
-    spi.beginTransaction(SPISettings(spi_write_speed * 1000000, MSBFIRST, TFT_SPI_MODE));
+    spi.beginTransaction(SPISettings(spi_write_speed * 1000000, MSBFIRST, SPI_MODE0));
     CS_L;
     SET_BUS_WRITE_MODE;
   }
@@ -247,7 +247,7 @@ inline void TFT_eSPI::begin_tft_write() {
 void TFT_eSPI::begin_nin_write() {
   if (locked) {
     locked = false; // Flag to show SPI access now unlocked
-    spi.beginTransaction(SPISettings(spi_write_speed * 1000000, MSBFIRST, TFT_SPI_MODE));
+    spi.beginTransaction(SPISettings(spi_write_speed * 1000000, MSBFIRST, SPI_MODE0));
     CS_L;
     SET_BUS_WRITE_MODE;
   }
@@ -281,7 +281,7 @@ inline void TFT_eSPI::begin_tft_read() {
   dmaWait();
   if (locked) {
     locked = false;
-    spi.beginTransaction(SPISettings(SPI_READ_FREQUENCY, MSBFIRST, TFT_SPI_MODE));
+    spi.beginTransaction(SPISettings(SPI_READ_FREQUENCY, MSBFIRST, SPI_MODE0));
     CS_L;
   }
   SET_BUS_READ_MODE;

lib/TFT_eSPI/TFT_eSPI.h

@@ -1,7 +1,5 @@
 #pragma once
 
-#define TFT_ESPI_VERSION "2.5.43"
-
 #include <Arduino.h>
 #include <SPI.h>
 
@@ -9,7 +7,6 @@
 
 #include <pgmspace.h>
 
-#define PROCESSOR_ID 0x32
 #define SPI_PORT VSPI
 #include "soc/spi_reg.h"
 #include "driver/spi_master.h"
@@ -22,7 +19,7 @@
 
 #define FS_NO_GLOBALS
 #include <FS.h>
-#include "SPIFFS.h" // ESP32 only
+#include "SPIFFS.h"
 
 #define DC_C GPIO.out_w1tc = (1 << TFT_DC)//;GPIO.out_w1tc = (1 << TFT_DC)
 #define DC_D GPIO.out_w1ts = (1 << TFT_DC)//;GPIO.out_w1ts = (1 << TFT_DC)
@@ -33,17 +30,13 @@
 #define WR_L
 #define WR_H
 
-#ifndef TFT_MISO
+#define TFT_MISO -1
-  #define TFT_MISO -1
+#define TFT_MOSI 23
-#endif
+#define TFT_SCLK 18
-
+#define TFT_CS 5
-#ifndef TFT_MOSI
+#define TFT_DC 17
-  #define TFT_MOSI 23
+#define TFT_RST 16
-#endif
+#define TOUCH_CS 32
-
-#ifndef TFT_SCLK
-  #define TFT_SCLK 18
-#endif
 
 #define TFT_WRITE_BITS(D, B) *_spi_mosi_dlen = B-1;    \
                               *_spi_w = D;             \
@@ -73,19 +66,10 @@
 // Write same value twice
 #define tft_Write_32D(C) TFT_WRITE_BITS((uint16_t)((C)<<8 | (C)>>8)<<16 | (uint16_t)((C)<<8 | (C)>>8), 32)
 
-////////////////////////////////////////////////////////////////////////////////////////
+#define tft_Read_8() spi.transfer(0)
-// Macros to read from display using SPI or software SPI
-////////////////////////////////////////////////////////////////////////////////////////
-#if !defined (TFT_PARALLEL_8_BIT)
-  #define tft_Read_8() spi.transfer(0)
-#endif
 
 #define DAT8TO32(P) ( (uint32_t)P[0]<<8 | P[1] | P[2]<<24 | P[3]<<16 )
 
-#ifndef TFT_SPI_MODE
-  #define TFT_SPI_MODE SPI_MODE0
-#endif
-
 //These enumerate the text plotting alignment (reference datum point)
 #define TL_DATUM 0 // Top left (default)
 #define TC_DATUM 1 // Top centre

lib/TFT_eSPI/User_Setup_Select.h

@@ -1,10 +1,5 @@
 #pragma once
 
-#define TFT_CS 5
-#define TFT_DC 17
-#define TFT_RST 16
-#define TOUCH_CS 32
-
 #define SPI_FREQUENCY 7500000
 #define SPI_READ_FREQUENCY 20000000
 #define SPI_TOUCH_FREQUENCY 2500000

platformio.ini

@@ -6,9 +6,7 @@ platform = espressif32
 upload_speed = 921600
 monitor_speed = 115200
 board = esp32dev
-framework = arduino, espidf
+framework = arduino
-board_build.f_flash = 80000000L
-board_build.f_cpu = 160000000L
 board_build.partitions = maxapp.csv
 build_flags =
     -Wall

sdkconfig.defaults

@@ -1,59 +0,0 @@
-CONFIG_APP_EXCLUDE_PROJECT_VER_VAR=y
-CONFIG_APP_EXCLUDE_PROJECT_NAME_VAR=y
-CONFIG_BOOTLOADER_LOG_LEVEL_ERROR=y
-CONFIG_BOOTLOADER_WDT_DISABLE_IN_USER_CODE=y
-CONFIG_BOOTLOADER_WDT_TIME_MS=1000
-CONFIG_ESPTOOLPY_FLASHFREQ_80M=y
-CONFIG_ESPTOOLPY_FLASHSIZE_4MB=y
-CONFIG_ESPTOOLPY_BEFORE_NORESET=y
-CONFIG_ESPTOOLPY_AFTER_NORESET=y
-CONFIG_PARTITION_TABLE_CUSTOM=y
-CONFIG_PARTITION_TABLE_CUSTOM_FILENAME="maxapp.csv"
-CONFIG_ARDUINO_RUN_CORE0=y
-CONFIG_ARDUINO_SELECTIVE_COMPILATION=y
-# CONFIG_ARDUINO_SELECTIVE_AsyncUDP is not set
-# CONFIG_ARDUINO_SELECTIVE_AzureIoT is not set
-# CONFIG_ARDUINO_SELECTIVE_BLE is not set
-# CONFIG_ARDUINO_SELECTIVE_BluetoothSerial is not set
-# CONFIG_ARDUINO_SELECTIVE_EEPROM is not set
-# CONFIG_ARDUINO_SELECTIVE_FFat is not set
-# CONFIG_ARDUINO_SELECTIVE_HTTPClient is not set
-# CONFIG_ARDUINO_SELECTIVE_LITTLEFS is not set
-# CONFIG_ARDUINO_SELECTIVE_NetBIOS is not set
-# CONFIG_ARDUINO_SELECTIVE_Preferences is not set
-# CONFIG_ARDUINO_SELECTIVE_SD is not set
-# CONFIG_ARDUINO_SELECTIVE_SD_MMC is not set
-# CONFIG_ARDUINO_SELECTIVE_SimpleBLE is not set
-# CONFIG_ARDUINO_SELECTIVE_Ticker is not set
-# CONFIG_ARDUINO_SELECTIVE_Update is not set
-# CONFIG_ARDUINO_SELECTIVE_WiFiClientSecure is not set
-# CONFIG_ARDUINO_SELECTIVE_WiFiProv is not set
-CONFIG_COMPILER_OPTIMIZATION_SIZE=y
-CONFIG_COMPILER_OPTIMIZATION_ASSERTIONS_DISABLE=y
-CONFIG_ESP32_REV_MIN_2=y
-# CONFIG_ESP32_DEBUG_OCDAWARE is not set
-# CONFIG_ETH_USE_ESP32_EMAC is not set
-# CONFIG_ETH_USE_SPI_ETHERNET is not set
-# CONFIG_ESP_HTTP_CLIENT_ENABLE_HTTPS is not set
-# CONFIG_ESP_HTTP_CLIENT_ENABLE_DIGEST_AUTH is not set
-# CONFIG_ESP_PHY_CALIBRATION_AND_DATA_STORAGE is not set
-CONFIG_PM_ENABLE=y
-CONFIG_PM_DFS_INIT_AUTO=y
-CONFIG_ESP_SYSTEM_PANIC_PRINT_HALT=y
-CONFIG_FREERTOS_HZ=1000
-CONFIG_FREERTOS_PLACE_SNAPSHOT_FUNS_INTO_FLASH=y
-CONFIG_HAL_ASSERTION_DISABLE=y
-CONFIG_LOG_DEFAULT_LEVEL_ERROR=y
-# CONFIG_LOG_COLORS is not set
-CONFIG_MBEDTLS_CMAC_C=y
-CONFIG_MBEDTLS_PSK_MODES=y
-CONFIG_MBEDTLS_KEY_EXCHANGE_PSK=y
-# CONFIG_MBEDTLS_KEY_EXCHANGE_DHE_PSK is not set
-# CONFIG_MBEDTLS_KEY_EXCHANGE_ECDHE_PSK is not set
-# CONFIG_MBEDTLS_KEY_EXCHANGE_RSA_PSK is not set
-# CONFIG_MQTT_PROTOCOL_311 is not set
-# CONFIG_MQTT_TRANSPORT_SSL is not set
-CONFIG_SPIFFS_MAX_PARTITIONS=1
-# CONFIG_SPIFFS_USE_MTIME is not set
-# CONFIG_WS_TRANSPORT is not set
-# CONFIG_UNITY_ENABLE_IDF_TEST_RUNNER is not set

src/CMakeLists.txt

@@ -1,6 +0,0 @@
-# This file was automatically generated for projects
-# without default 'CMakeLists.txt' file.
-
-FILE(GLOB_RECURSE app_sources ${CMAKE_SOURCE_DIR}/src/*.*)
-
-idf_component_register(SRCS ${app_sources})

src/main.cpp

@@ -1079,7 +1079,10 @@ void setAutoSpeedSPI() {
 }
 
 void endMenu() {
-  if(rds_settings_changed) radio.clearRDS(fullsearchrds);
+  if(rds_settings_changed) {
+    radio.clearRDS(fullsearchrds);
+    RDSstatus = false;
+  }
   rds_settings_changed = menu = false;
   menuopen = false;
   LowLevelInit = true;
@@ -1175,7 +1178,7 @@ void setup() {
   bool tef_found = false;
 
   Wire.begin();
-  Wire.setClock(400000);
+  Wire.setClock(100000);
   delay(1);
 
   Serial.begin(115200);
@@ -2833,9 +2836,9 @@ void DoMemoryPosTune() {
   if (RDSSPYTCP) RemoteClient.print("G:\r\nRESET-------\r\n\r\n");
   if (XDRGTKUSB || XDRGTKTCP) DataPrint("T" + String((frequency + ConverterSet * 100) * 10) + "\n");
 
-  String stationText = "";
+  String stationName = "";
   if (presets[memorypos].RDSPS[0] != '\0') {
-    for (byte i = 0; i < 9; i++) stationText += presets[memorypos].RDSPS[i];
+    for (byte i = 0; i < 9; i++) stationName += presets[memorypos].RDSPS[i];
   }
 
   if (presets[memorypos].RDSPI[0] != '\0') {
@@ -2848,7 +2851,7 @@ void DoMemoryPosTune() {
     for (byte i = 0; i < 6; i++) radio.rds.picode[i] = '\0';
   }
 
-  radio.rds.stationName = stationText;
+  radio.rds.stationName = stationName;
 
   BWset = presets[memorypos].bw;
   doBW();
@@ -3981,21 +3984,3 @@ uint8_t doAutoMemory(uint16_t startfreq, uint16_t stopfreq, uint8_t startmem, ui
 
   return error;
 }
-
-extern "C" {
-  void app_main() {
-    rtc_wdt_disable();
-    rtc_wdt_protect_off();
-
-    initArduino();
-
-    setup();
-
-    rtc_wdt_enable();
-    rtc_wdt_protect_on();
-    while(true) {
-      loop();
-      rtc_wdt_feed();
-    }
-  }
-}

src/rds.cpp

@@ -5,8 +5,8 @@
 String HexStringold;
 float smoothBER = 0;
 
-int PSLongWidth, AIDWidth, lengths[7];
+int AIDWidth, lengths[7];
-String stationNameLongOld, AIDStringold;
+String AIDStringold;
 bool rtABold, ps12errorold, ps34errorold, ps56errorold, ps78errorold;
 
 void ShowAdvancedRDS() {
@@ -431,11 +431,6 @@ void showPS() {
       if (!screenmute) tftReplace(ACENTER, PSold, radio.rds.stationName, 160, 201, BWAutoColor, BWAutoColorSmooth, BackgroundColor, 16);
     } else if (!rdsstatscreen) {
       if (radio.rds.hasLongPS && showlongps) {
-        if (radio.rds.stationNameLong != stationNameLongOld) {
-          PSLongWidth = PSSprite.textWidth(radio.rds.stationNameLong); // Measure new width
-          stationNameLongOld = radio.rds.stationNameLong;
-        }
-
         lpsDisplay.update(radio.rds.stationNameLong, RDSstatus, RDSColor, RDSColorSmooth, RDSDropoutColor, RDSDropoutColorSmooth, BackgroundColor);
       } else {
         lpsDisplay.reset();