You've already forked TEF6686_ESP32
Comments removed
This commit is contained in:
Sjef Verhoeven PE5PVB
@@ -1,179 +1,3 @@
|
|||||||
/*
|
|
||||||
********************************************************************************
|
|
||||||
Advanced Tuner software for NXP TEF668x ESP32
|
|
||||||
(c) 2023 Sjef Verhoeven pe5pvb@het-bar.net
|
|
||||||
Based on Catena / NXP semiconductors API
|
|
||||||
********************************************************************************
|
|
||||||
v1.00 - Release
|
|
||||||
v1.01 - Add interrupt on both Rotary pins
|
|
||||||
- Add default settings
|
|
||||||
- Add Standby function
|
|
||||||
- Forced reboot after XDR-GTK disconnect
|
|
||||||
v1.02 - Fixed signalstrenght display when
|
|
||||||
value is 0 after boot or isn't changed
|
|
||||||
after menu close
|
|
||||||
- Added stepsize option
|
|
||||||
- Show "<" when signallevel is below
|
|
||||||
0dBuV. Showing negative value is very
|
|
||||||
unstable.
|
|
||||||
- Cosmetic improvements
|
|
||||||
v1.03 - When signallevel is < set value all
|
|
||||||
statusses will only be updated
|
|
||||||
every 0.5 seconds. Threshold can be
|
|
||||||
set in the menu. RDS is then disabled
|
|
||||||
This will also improve I2C and ADC
|
|
||||||
noise on low level signals.
|
|
||||||
- System can now show negative dBuV.
|
|
||||||
v1.04 - Optimised TEF initialisation
|
|
||||||
- Fix on peakhold modulation meter
|
|
||||||
- Added Stereo squelch (turn knob right)
|
|
||||||
- Added Squelch off (turn knob left)
|
|
||||||
- Show current Squelch threshold
|
|
||||||
v1.05 - Fixed bug: Patch was not loaded
|
|
||||||
correctly into tuner after boot
|
|
||||||
- In Low level mode, RDS logo disabled
|
|
||||||
- Fix Stereo/mono toggle when using
|
|
||||||
XDR-GTK
|
|
||||||
- Fixed Squelch level readout when
|
|
||||||
leaving menu. This could cause auto-
|
|
||||||
scan to not work.
|
|
||||||
- Fix: RDS logo was not disabled in low
|
|
||||||
signal level mode
|
|
||||||
- Changed advice for TFT frequency to
|
|
||||||
reduce unwanted noise
|
|
||||||
- Optimised soft-boot
|
|
||||||
v1.06 - Slow down I2C speed to reduce noise
|
|
||||||
- Fix auto scan when squelch level is
|
|
||||||
below 0dBuV
|
|
||||||
- Fix show Hz (not kHz) on high cut
|
|
||||||
corner frequency
|
|
||||||
v1.07 - Added multipath suppresion (iMS) and
|
|
||||||
Channel Equalizer (EQ)
|
|
||||||
- Long press rotary to toggle iMS and EQ
|
|
||||||
- Added standby LED on D19
|
|
||||||
- XDR-GTK: Use the antenna rotor buttons
|
|
||||||
to start scan up or down
|
|
||||||
- XDR-GTK: Enable IF+ to force low
|
|
||||||
signal level mode
|
|
||||||
- XDR-GTK: DX1 = Normal
|
|
||||||
DX2 = iMS enabled
|
|
||||||
DX3 = EQ enabled
|
|
||||||
DX4 = Both enabled
|
|
||||||
- Small modifications on XDR-GTK routine
|
|
||||||
for compatibility with modified
|
|
||||||
XDR-GTK TEF6686 edition
|
|
||||||
- Fixed small bug with displaytext in
|
|
||||||
scan mode
|
|
||||||
v1.08 - Fixed interrupted canvas lines on TFT
|
|
||||||
- Added function to mute TFT using XDR-
|
|
||||||
GTK. Use RF+ to use this function
|
|
||||||
- Level offset is still as set when
|
|
||||||
using XDR-GTK
|
|
||||||
- Detach interrupts when writing
|
|
||||||
frequency to display, to prevent
|
|
||||||
display crash
|
|
||||||
- Fixed bug when squelch is set to -1
|
|
||||||
- Fixed bug that volume offset was reset
|
|
||||||
to 0 after changing frequency
|
|
||||||
v1.09 - Stereo indication didn't work when RF+
|
|
||||||
was set in XDR-GTK
|
|
||||||
- Minor fix: When for some reason the
|
|
||||||
signallevel was an invalid value, now
|
|
||||||
the limit is -10 to +120dBuV
|
|
||||||
- No more short mute when changing frequency
|
|
||||||
- tuned indication only on when signal
|
|
||||||
valid.
|
|
||||||
- In Auto mode frequency is now shown and
|
|
||||||
direction can be changed on the fly.
|
|
||||||
to stop searching, just press any key.
|
|
||||||
- Minor bugfix in low signal lever timer.
|
|
||||||
v1.10 - Stand-by function was bricked after last update.
|
|
||||||
- Code optimised for compiler v2.0.0.
|
|
||||||
- Startup frequency was always 100.0MHz. Fixed.
|
|
||||||
v1.11 - Maximum frequency changed to 108MHz. (110MHz is not possible).
|
|
||||||
- Added AM reception.
|
|
||||||
- Hold BW button during boot to change direction of
|
|
||||||
rotary encoder.
|
|
||||||
- Hold Mode button during boot to flip the screen.
|
|
||||||
- When RT was too long the canvas was overwritten.
|
|
||||||
v1.12 - Stand-by key caused an issue when in menu mode.
|
|
||||||
- Canvas was broken on some points in the screen.
|
|
||||||
- Added possibility to connect analog signalmeter (thanks David DSP)
|
|
||||||
- Added slow signalmeter riding (thanks David DSP)
|
|
||||||
- S-meter for AM is corrected to the right values.
|
|
||||||
v1.13 - Fix for frequency offset in AM.
|
|
||||||
- Fix for flickering signalmeter when fluctuation is < 1dBuV.
|
|
||||||
- Added support for David DSP's converter board.
|
|
||||||
v1.14 - Bugfix: When signallevel drops down in digits, old digits were still displayed.
|
|
||||||
v1.15 - Fix AM bandwidth setting on F6805 chipset
|
|
||||||
- Added microcode for whole TEF668x family (Lithio)
|
|
||||||
- Added C/N readout
|
|
||||||
- S-meter and modulation meter update (Thanks David DSP)
|
|
||||||
- Added splash screen with tuner info
|
|
||||||
- Fixed problem when tuning beyond bandlimits on AM
|
|
||||||
- FM level calibrated
|
|
||||||
- Function added to choose between regular and optical rotary encoder (hold rotary button during boot)
|
|
||||||
v1.16 - Fixed some bugs to make the script compatible with new boardmanagers (v2.x)
|
|
||||||
- Rewritten rotary encoder routines
|
|
||||||
- New RDS routine
|
|
||||||
- Massive code cleanup
|
|
||||||
- Fixed canvas when changing bands
|
|
||||||
- Radiotext auto scroll when it does not fit in the window
|
|
||||||
- Added RDS CT (clock only)
|
|
||||||
- Added FullSearchRDS for TEF6687 & TEF6689
|
|
||||||
- Added AM/FM indicator
|
|
||||||
- Fixed S-meter averaging
|
|
||||||
- Improved XDRGTK RDS output
|
|
||||||
- On signal dropout, RDS PTY, PI and PS stays on screen in blue
|
|
||||||
********************************************************************************
|
|
||||||
|
|
||||||
Analog signalmeter:
|
|
||||||
to meter
|
|
||||||
|
|
|
||||||
R V
|
|
||||||
IO27 -------=====-----=====---|
|
|
||||||
1 k 5 k POT
|
|
||||||
|
|
||||||
********************************************************************************
|
|
||||||
Setup:
|
|
||||||
During boot:
|
|
||||||
Hold BW button to change rotary encoder direction
|
|
||||||
Hold Mode button the flip screen
|
|
||||||
Hold Standby button to calibrate analogue s-meter
|
|
||||||
Hold rotary button to switch between normal and optical rotary encoder
|
|
||||||
|
|
||||||
Manual:
|
|
||||||
STANDBY SHORT PRESS: Switch band
|
|
||||||
STANDBY LONG PRESS: Standby
|
|
||||||
ROTARY SHORT PRESS: Set stepsize or navigate
|
|
||||||
ROTARY LONG PRESS: Toggle iMS & EQ
|
|
||||||
MODE SHORT PRESS: Switch between auto/manual
|
|
||||||
or exit menu
|
|
||||||
MODE LONG PRESS: Open menu
|
|
||||||
BW SHORT PRESS: Switch bandwidth setting
|
|
||||||
BW LONG PRESS: Switch mono, or auto stereo
|
|
||||||
* ***********************************************
|
|
||||||
|
|
||||||
|
|
||||||
Use this settings in TFT_eSPI User_Setup.h
|
|
||||||
#define ILI9341_DRIVER
|
|
||||||
#define TFT_CS 5
|
|
||||||
#define TFT_DC 17
|
|
||||||
#define TFT_RST 16
|
|
||||||
#define LOAD_GLCD
|
|
||||||
#define LOAD_FONT2
|
|
||||||
#define LOAD_FONT4
|
|
||||||
#define LOAD_FONT6
|
|
||||||
#define LOAD_FONT7
|
|
||||||
#define LOAD_FONT8
|
|
||||||
#define LOAD_GFXFF
|
|
||||||
#define SMOOTH_FONT
|
|
||||||
#define SPI_FREQUENCY 10000000
|
|
||||||
|
|
||||||
ALL OTHER SETTINGS SHOULD BE REMARKED!!!!
|
|
||||||
|
|
||||||
*/
|
|
||||||
|
|
||||||
#include "src/TEF6686.h"
|
#include "src/TEF6686.h"
|
||||||
#include "src/constants.h"
|
#include "src/constants.h"
|
||||||
#include <EEPROM.h>
|
#include <EEPROM.h>
|
||||||
|
|||||||
Reference in New Issue
Block a user